Just how do you actually feel when it comes to A Step-by-Step Guide to Installing a Bathtub?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard job. If the old tub is readily accessible, the task can relocate immediately; if you need to open a wall surface to get rid of the old tub and also position the brand-new tub, the job is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly require an assistant to move out the old bathtub as well as embeded in the new one. See to it you have actually certified on your own for the job as well as are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed project, it is better to think about utilizing one before you start. Chances are you might require an expert plumber to make tube connections.
This article will help you install a new bath tub in your bathroom if you have actually currently gotten a brand-new bathtub as well as do not need to alter the setup of your previous water supply pipes.
Your devices and also product list must consist of the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, after that the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly problematic due to the limited accessibility that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been removed, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin making certain that the washers remain in location between the faucet and the sink. Safeguard the tap in position with the producer provided backnut. Once the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet adapters. The previous kind should be attached to the tap finishes initially, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the required position. The wood boards are practical in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four tiny points.
The following objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and adjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit the bottom of the furthest versatile faucet adapter to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water system as well as check all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill up the tub and likewise check the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, repair the bathroom paneling as explained in the maker's instruction manual. Tiling and also securing around the tub must wait until the bath tub has actually been utilized a minimum of once as this will certainly settle it right into its last setting.
Getting ready for the Setup
Firstly, the supporting framework supplied with the bath needs to be fitted (if called for) according to the producer's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps device to prevent strain on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its last setting.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to crack an inflexible seal, triggering the water to penetrate the wall between the bath as well as the tiling, bring about difficulties with moisture as well as possible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and also installations. They are sold in tubes and cartridges, and also can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to always fill the bathtub with water before securing, to permit the movement experienced when the tub is in use. The sealer can break relatively early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that content on How to Install a Bathtub while doing a search on the internet. Those who appreciated our blog entry plz make sure you remember to share it. I thank you for reading our article about A Step-by-Step Guide to Installing a Bathtub.
Burst pipes? Get immediate help.